Combustion

From CFD-Wiki

(Difference between revisions)

Revision as of 10:38, 3 October 2005

What is combustion -- Physics versus modelling

Combustion phenomena consists of many physical and chemical processes with broad range of time scales. Mathematical description of combustion is not always trivial. Analytical solutions exists only for basic situations of laminar flame and because of its assumptions it is often restricted to few problems solved usually in zero or one-dimensional space.

Problems solved today concern mainly turbulent flows, gas as well as liquid fuels, pollution issues (products of combustion as well as for example noise pollution). These problems require not only extensive experimental work, but also numerical modelling. All combustion models must be validated against the experiments as each one has its own drawbacks and limits. However here the modelling part will be mainly addressed.

Reaction mechanisms

The combustion is mainly chemical process and although we can, to some extend, describe flame without any chemistry informations, for modelling of flame propagation we need to know the speed of reactions, product concentrations, temperature and other parameters. Therefore more or less detailed information about reaction kinetics is essential for any combustion model. Mixture will generally combust, if the reaction of fuel and oxidiser is fast enough to maintain until all of the mixture is burned into products. If the reaction is too slow, the flame will extinguish, if too fast, explosion or even detonation will occur. The reaction rate of typical combustion reaction is influenced mainly by concentration of reactants, temperature and pressure.

A stoichiometric equation of an arbitrary equation can be written as:

$\sum_{j=1}^{n}\nu' (M_j) = \sum_{j=1}^{n}\nu'' (M_j),$

where $\nu$ is the stoichiometric coefficient, $M_j$ is arbitrary species. One prime specifies the reactants and double prime products of the reaction.

Reaction rate, expressing the rate of disappearance of reactant i of such a reaction, is defined as:

$RR_i = k \, \prod_{j=1}^{n}(M_j)^{\nu'},$

in which k is the specific reaction rate constant. Arrhenius found that this constant is a function only of temperature and this function is defined as:

$k= A T^{\beta} \, exp \left( \frac{-E}{RT}\right)$

where A is pre--exponential factor, E is activation energy and $\beta$ is temperature exponent. These constants for given reactions can be found in literature. The reaction mechanism can be given from experiments for every reaction resolved, it could be also constructed numerically by automatic generation method (see [Griffiths (1994)] for review on reaction mechanisms). For simple hydrocarbon tens to hundreds of reactions are involved. By analysis and systematic reduction of reaction mechanisms global reaction (from one to five step reactions) can be found (see [Westbrook (1984)]).

Governing Equations for Reacting Flows

Togetehr with the usual Navier-Stokes for compresible flows (See Governing Equations), additional equations are used The mass fraction transport equation for k-th species $Y_k$

$\frac{\partial}{\partial t} \left( \rho Y_k \right) + \frac{\partial}{\partial x_j} \left( \rho u_j Y_k\right) = \frac{\partial}{\partial x_j} \left( \rho D_k \frac{\partial Y_k}{\partial x_j}\right)+ \dot w_k$

</td></tr>

(1)

where Ficks law is assumed for scalar diffusion and $\dot w_k$ is the species reaction rate.

Infinitely fast chemistry

All combustion models can be divided into two main groups according to the assumptions on the reaction kinetics. We can either assume the reactions to be infinitely fast - compared to e.g. mixing of the species, or of the comparable time scale of the mixing process. The simpler approach assuming chemistry fast enough, that the limiting process is mixing of the species is historically older approach and even today can be appropriate approach. It is simpler to solve then #Finite rate chemistry models, but introduces errors to the solution which may or may not be important.

Premixed Combustion

Premixed flame occurs in mixtures of fuel and oxidiser, homogeneously premixed prior to the flame. These flames are not limited only to gas fuels, but also to the pre-vaporised fuels. Typical example of premixed laminar flame is bunsen burner, where the air enters the fuel stream. The mixture burns in the wake of the riser tube walls forming nice stable flame. The premixed flames has many advantages in terms of control of temperature and products and pollution concentration, but introduce also some dangers like the autoignition (in the supply system).

Turbulent flame speed model

Eddy Break-Up model

The Eddy Break-Up model is the typical example of mixed-is-burnt combustion model. It is based on the work of Magnussen and Hjertager, and Spalding and can be found in all CFD packages. The model assumes the reactions to be completed in the moment of mixing, so that the reaction rate is completely controlled by turbulent mixing. The combustion is described by a single step global chemical reaction:

$F + \nu_s O \rightarrow (1+\nu_s) P$

in which F stands for fuel, O for oxidiser and P for products of the reaction. Alternativelly we can have multistep scheme, where each reaction has its own mean reaction rate. The mean reaction rate is given by:

$\bar{\dot\omega}_F=A_{EB} \frac{\epsilon}{k} min\left[\bar{C}_F,\frac{\bar{C}_O}{\nu}, B_{EB}\frac{\bar{C}_P}{(1+\nu)}\right]$

$\bar{C}$ denotes mean concentrations for fuel, oxidiser and products respectively, A and B are model constants with typical values of 0.5 and 4.0 respectively. The values of these constants are fitted according to the experimental results and they are suitable for most of the general cases. Still they are just constants based on experimental fitting and they need not be suitable for all the situations. Care must be taken especially in highly strained regions, where the ratio of $k$ to $\epsilon$ is large (flame-holder wakes, walls ...). In those regions a positive reaction rate occurs and an artificial flame can be observed. CFD codes usually has some remedies to overcome this problem.

This model largely over-predicts temperatures and concentrations of species like CO and other species. Still this model is quite popular for its simplicity and relatively easy convergence and implementation.

Bray-Moss-Libby Model

Non premixed combustion

Conserved scalar equilibrium models

Finite rate chemistry

Premixed Combustion

Coherent Flame Model

Flamelets based on G equation

Non-premixed Combustion

Flamelets based on conserved scalar

Peters (2000) define Flamelets as "thin diffusion layers embedded in a turbulent non-reactive flow field". If the chemistry is fast enough, the chemistry is active within a thin region where the chemistry conditions are in (or close to) stoichiometric conditions, the "flame" surface. This thin region is assumed to be smaller than Kolmogorov length scale and therefore the region is locally laminar. The flame surface is defined as an iso-surface of a certain scalar $Z$ , mixture fraction in non-premixed combustion.

The reactive problems is therefore split into two parts: First, the mixing , which consists of the location of the flame surface which is a non-reactive problem concerning the propagation of a passive scalar. And second, the flame structure , which deals with the distribution of the reactive species inside the flamelet.

To obtain the distribution inside the flame front we assume it is locally one-dimensional and depends only on time and the scalar coodinate.

Using the following chain rules for the time

$\frac{\partial Y_k}{\partial t} = \frac{\partial Z}{\partial t}\frac{\partial Y_k}{\partial Z}$

and spatial coordinate

$\frac{\partial Y_k}{\partial x_j} = \frac{\partial Z}{\partial x_j}\frac{\partial Y_k}{\partial Z}$

to the species transport equation Governing Equations and re-arranging, we obtain

$\rho \frac{\partial Y_k}{\partial t} + Y_k \left[ \frac{\partial \rho}{\partial t} + \frac{\partial \rho u_j}{\partial x_j} \right] + \frac{\partial Y_k}{\partial Z} \left[ \rho \frac{\partial Z}{\partial t} + \rho u_j \frac{\partial Z}{\partial x_j} - \frac{\partial}{\partial x_j}\left( \rho D \frac{\partial Z}{\partial x_j} \right) \right] = \rho D \left( \frac{\partial Z}{\partial x_j} \frac{\partial Z}{\partial x_j} \right) + \dot w_k$

The second and third term in the LHS cancel due to continuity and mixture fraction transport, the equation therefore boils down to

$\frac{\partial Y_k}{\partial t} = \frac{\chi}{2} \frac{\partial ^2 Y_k}{\partial Z^2} + \dot w_k$

where $\chi = 2 D \left( \frac{\partial Z}{\partial x_j} \right)^2$ is called the scalar dissipation and controls the mixing, providing the interaction between the flow and the chemistry.

This approach is called the Stationary Laminar Flamelet Model (SLFM) and has the advantage that libraries of $Y_k=f(Z,\chi)$ can be pre-computed and stored in look-up tables with all the required complex chemistry.

Conditional Moment Closure (CMC)

Multiple Mapping Closure (MMC)

Linear Eddy Model

PDF transport models

Lagrangian

Eulerian

References

Griffiths J.F. (1994), "Reduced Kinetic Models and Their Application to Practical Combustion Systems", Prog. in Energy and Combustion Science,Vol. 21, pp. 25-107.
Westbrook, Ch.K., Dryer,F.L., (1984), "Chemical Kinetic Modeling of Hydrocarbon Combustion", Prog. in Energy and Combustion Science,Vol. 10, pp. 1-57.

@@ Line 69: / Line 69: @@
 (from one to five step reactions) can be found (see [Westbrook (1984)]).
-== Governing Equations ==
+== Governing Equations for Reacting Flows ==
+Togetehr with the usual Navier-Stokes for compresible flows (See [[Governing Equations]]), additional equations are used
 The mass fraction transport equation  for <i>k-th</i> species <math> Y_k </math>

Combustion

From CFD-Wiki

Revision as of 10:38, 3 October 2005

Contents

What is combustion -- Physics versus modelling

Reaction mechanisms

Governing Equations for Reacting Flows

Infinitely fast chemistry

Premixed Combustion

Turbulent flame speed model

Eddy Break-Up model

Bray-Moss-Libby Model

Non premixed combustion

Conserved scalar equilibrium models

Finite rate chemistry

Premixed Combustion

Coherent Flame Model

Flamelets based on G equation

Non-premixed Combustion

Flamelets based on conserved scalar

Conditional Moment Closure (CMC)

Multiple Mapping Closure (MMC)

Linear Eddy Model

PDF transport models

Lagrangian

Eulerian

References

External links and sources

Views

My wiki

wiki navigation

wiki search

wiki toolbox