CHAM FAQ

From CFD-Wiki

Revision as of 11:55, 16 June 2016

This article contains FAQs for the PHOENICS CFD code. The structure of this FAQ page is still evolving according to the number and type of questions that are frequently asked.

PHOENICS

General

What is PHOENICS?

PHOENICS is a general-purpose commercial CFD code which is applicable to steady or unsteady, one- , two- or three-dimensional turbulent or laminar, multi-phase, compressible or incompressible flows using Cartesian, cylindrical-polar or curvilinear coordinates. The code also has a spatial marching integration option to handle parabolic and hyperbolic flows, as well as transonic free jets in the absence of recirculation zones.

The numerical procedure is of the finite-volume type in which the original partial differential equations are converted into algebraic finite-volume equations with the aid of discretisation assumptions for the transient, convection, diffusion and source terms. For this purpose, the solution domain is subdivided into a number of control volumes on a mono-block mesh using a conventional staggered-grid approach. All field variables except velocities are stored at the grid nodes, while the velocities themselves are stored at staggered cell-face locations which lie between the nodes.

For curvilinear coordinates, the default option is to solve the momentum equations in terms of the covariant projections of the velocity vector into the local grid directions on a structured, mono-block, staggered mesh. An alternative exists to employ the GCV method for curvilinear coordinates, whereby cell-centred Cartesian velocities or covariant velocity projections are solved on a structured mono-block or multi-block mesh. The link description for the latter can handle arbitrary block rotations, and therefore can accommodate an unstructured multi-block grid made from relatively simple, structured blocks.

For complex geometries, PHOENICS by default actually uses a Cartesian cut-cell method named PARSOL which provides an automatic, efficient, and flexible alternative to traditional boundary-fitted grid methods using curvilinear coordinates. The Cartesian cut-cell approach uses a background Cartesian or cylindrical-polar grid for the majority of the flow domain with special treatments being applied to cells which are cut by solid bodies, thus retaining a boundary-conforming grid. Specifically, the method computes the fractional areas and volumes, and employs a collection of special algorithms for computing interfacial areas, evaluating wall shear stresses, and for computing advection and diffusion near solid boundaries, etc.

The finite-volume equations for each variable are derived by integrating the partial differential equations over each control volume. Fully implicit backward differencing is employed for the transient terms, and central differencing is used for the diffusion terms. The convection terms are discretised using hybrid differencing in which the convective terms are approximated by central differences if the cell face Peclet number is less than 2 and otherwise by upwind differencing. At faces where the upwind scheme is used, physical diffusion is omitted altogether. In addition to the upwind and hybrid differencing schemes, PHOENICS is furnished with an extensive set of higher-order convection schemes, which comprise five linear schemes and twelve non-linear schemes. The linear schemes include CDS, QUICK, linear upwind and cubic upwind. The non-linear schemes employ a flux limiter to secure boundedness. These schemes include SMART, H-QUICK, UMIST, SUPERBEE, MINMOD, OSPRE, MUSCL and van-Leer harmonic.

The integration procedure results in a coupled set of algebraic finite-volume equations which express the value of a variable at a grid node in terms of the values at neighbouring grid points and the nodal value at the old time level. For unsteady flows, PHOENICS by default solves each of these equations by an implicit method, but the option exists to revert to an explicit method which is stable only when the Courant number is less than or equal to unity. The explicit method uses old-time neighbour values, whereas the implicit method uses values at the new time level. Although implicit methods allow a much larger Courant number than the explicit methods, it is not unconditionally stable since the non-linearities in the equations often limit numerical stability.

The finite-volume equations are solved iteratively using the SIMPLEST and IPSA algorithms of Spalding, which are embodied in PHOENICS for the solution of single-phase and two-phase flows, respectively. These algorithms are segregated solution methods which employ pressure-velocity coupling to enforce mass conservation by solving a pressure-correction equation and making corrections to the pressure and velocity fields. Multi-phase flows are accommodated using either an Eulerian-Lagrangian method using particle tracking, or an algebraic-slip model. The latter solves mixture continuity and momentum equations, and a volume-fraction equation is solved for each dispersed phase. Algebraic relationships are used for slip velocities relative to the mixture.

The default calculation procedure is organised in a slab-by-slab manner in which all dependent variables are solved in turn at the current slab before attention moves to the next higher slab. The slabs are thus visited in turn, from the lowermost to the uppermost, and a complete series of slab visits is referred to as a sweep through the solution domain. For parabolic and hyperbolic calculations, only one such sweep is required, with many iteration cycles at each slab for parabolic cases, and no outflow boundary condition is required because this is an outcome of the solution. For elliptic calculations, many such sweeps are conducted until convergence is attained at the current time level; in addition, the pressure-correction equation is solved in a simultaneous whole-field manner at the end of each sweep. Thereafter the solution proceeds to the next time level where the iterative process is repeated. The option exists to solve each finite-volume equation in a whole-field manner, and this is actually the default when using the automatic convergence control. The default linear equation solver for each finite-volume equation is a modified form of Stone's strongly implicit solver, but the option exists to use a Conjugate Gradient Residuals solver for each equation.

The GCV method solves the system of algebraic finite-volume equations by using a conjugate-residual linear solver with LU preconditioning, and it uses a segregated pressure-based solver strategy with an additional correction of the cell-centred momentum velocities. This provides faster convergence than conventional one-step face-velocity corrections.

The numerical solution procedure requires appropriate relaxation of the flow variables in order to procure convergence. Two types of relaxation are employed, namely inertial and linear. The former is normally applied to the velocity variables, whereas the latter is applied to all other flow variables, as and when necessary.

The PHOENICS Parallel solver subdivides the solution domain into sub-domains (spatial domain decomposition) and assigns each sub-domain to one processor on a multi-core computer. Each sub-domain has storage overlap ("halo" cells) for data exchange between the various sub-domains. The CFD code then runs simultaneously on all the processors, on its own set of data, and data is exchanged between the various sub-domains ( via the "halo" cells ) using MPI (message-passing interface). A point solver is used for whole-field solution of each of the finite-volume equations.

The convergence requirement is that for each set of finite-volume equations the sum of the absolute residual sources over the whole solution domain is less than one percent of references quantities based on the total inflow of the variable in question. An additional requirement is that the values of monitored dependent variables at a selected location do not change by more than 0.1 percent between successive iteration cycles. It is also possible to monitor the absolute values of the largest corrections to each variable anywhere in the domain. Once the largest correction falls to zero, or at least a negligible fraction of the value being corrected, then it can be assumed that convergence has been achieved, even if the sum of the residuals has not fallen below the cut-off.

Problem Set Up

Meshing

Geometry

Physical properties

Physical Modelling

General

Boundary Conditions

Turbulence Modelling

Numerical

Convergence

Relaxation

User Programming

PIL

In-Form

What is In-Form?

In-Form is a supplement to the PHOENICS Input Language (PIL) which facilitates the input of problem-defining data. Specifically, it allows users to express their requirements through algebraic formulae, whether for:

• space and time discretization,
• material properties,
• initial values,
• sources,
• boundary conditions,
• body shapes and motions, or
• special print-out features.

The formulae are placed in the data-input file, Q1 by way of a text editor, or via the graphical user interface of PHOENICS, the Virtual-Reality Editor.

The PHOENICS input module, Satellite, thereafter transmits the implications of the formulae to the solver module, EARTH. There they are recognised as instructions to perform the appropriate computations. The user has nothing more to do except await and inspect the computed results.

Extensive documentation of the In-Form facility is provided here: [1], and here: [2].

How can I obtain plots of, say temperature vs time for a transient simulation?

The In-Form facility can be used to output the values of particular variables at multiple locations as a function of time, as exemplified by the following INFORM command in Group 21 of the Q1 input file:

• save21begin

(table in monplt.csv is get(TEM1[5,17,6],TEM1[15,17,6],TEM1[25,17,6],TEM1[35,17,6]) with head(T5,T15,T25,T35)!time)

• save21end

This command writes to a file named "monplt.csv" (MS Excel format) at each time step, the field values of the temperature TEM1 at the grid locations (5,17,6), (15,17,6),(25,17,6) and (35,17,6). Alternatively, you can specify the (x,y,z) cartesian coordinates of the location where you want to tabulate the computed field values. For this, you use curly brackets {} instead of straight brackets []. So, for example, to tabulate TEM1 values at (2.1,0.8,9.6), you would use the following INFORM commands:

• save21begin

(table in montem.csv is get(TEM1{2.1,0.8,9.6}) with head(TEM1)!time)

• save21end

There is an INFORM tutorial explaining the method here: [3].

GROUND

Solver Methodology

PARSOL

What is PARSOL?

PARSOL stands for PARtial SOLids. It is a Cartesian cut-cell CFD method for solving flow in and around complex geometries. The method provides an automatic, efficient, and flexible alternative to traditional boundary-fitted grid methods using curvilinear coordinates for the representation of complex geometries. The Cartesian cut-cell approach uses a background Cartesian or cylindrical-polar grid for the majority of the flow domain with special treatments being applied to cells which are cut by solid bodies, thus retaining a boundary-conforming grid. Specifically, the method computes the fractional areas and volumes, and employs a collection of special algorithms for computing interfacial areas, evaluating wall shear stresses, and for computing advection and diffusion near solid boundaries, etc.

S-PARSOL

What is S-PARSOL?

S-PARSOL stands for Structured PARSOL, and it considers cut links rather than the cut edges of cells like PARSOL, a link being the line joining two cell-center nodes ( these links can be seen by clicking on the "S-PARSOL grid-line dialogue" button in the VR Environment ). S-PARSOL therefore creates no cut-cell control volumes or corresponding equations; but rather it makes changes to the finite-volume coefficients to represent the interactions between the fluid and the solid materials.

S-PARSOL has the substantial advantage over PARSOL of being able to detect thin solids without the need for high mesh densities. Also, S-PARSOL more accurately represents conjugate heat transfer through thin solids and composite media. S-PARSOL's practice of setting to zero the velocities in cut links has the advantage over PARSOL of recognising the presence of thin bodies, but this practice sometimes creates flow patterns of unpleasing appearance, which is why an improved version called X-PARSOL is being developed which is intended to combine the benefits of the earlier techniques without their deficiencies. A fairly detailed technical description of S-PARSOL is given in Section 3.3 of the following paper:

Spalding, D.B. (2013), "Trends, Tricks & Try-ons in CFD/CHT"", In Advances in Heat Transfer, Vol. 45, pp. 1-78, Editors: Ephraim M. Sparrow, Young I. Cho, John P. Abraham & John M. Gorman, Academic Press, Elsevier Inc. A pdf copy of this paper can be accessed here: S-PARSOL paper

Parallel

Pre-Processing

VR Editor

Post-Processing

VR Viewer

AUTOPLOT

PHOTON

Installation

How can I download the latest version of PHOENICS?

You can download the latest delivery version of PHOENICS 2015 (dated 31 March 2016) from CHAM’s FTP site, in either 32bit or 64bit form, by following the download instructions, a copy of which can be provided on request by emailing support@cham.co.uk with details of your name and organisation.

PHOENICS-FLAIR

General

What is PHOENICS-FLAIR?